How To Install A Wall Microwave

1. ane

   Utilise an appropriate microwave. A recirculating or front-venting microwave tin be installed below a counter without whatever farther effort. Other types may require more avant-garde ventilation installation. Be aware of the requirements of your model before you begin installation.

   • Other types of microwave may be more than suited for an over the range installation, require a new ventilation hood, or even necessitate a total new ventilation system.

2. two

   Locate the wall studs. Follow these methods for finding and marking these vertical wall supports. Your microwave will need to be fastened to at least one of them.^[one]

   • If you accept one, employ an electronic or magnetic stud finder to search for nails.
   • Alternately, tap lightly on the wall with a hammer. When you hear a solid "thunk" instead of a hollow sound, you've probable establish a wall stud.
   • If you're non certain whether you've found a stud, drill a test hole and employ a bent wire or coat hanger to search for solid objects in your wall.^[2]
   • One time you lot've located the center of one wall stud, its closest neighbors are usually located either 16 inches or 24 inches to each side.^[iii]
   • Employ a pocket-size boom to probe the wall stud(s) and make up one's mind the width.^[iv]
   • Draw a vertical line down the center of the wall studs in one case y'all've found them.

   Advertisement

3. 3

   Place the mounting plate. This flat metal plate should exist level and the top tabs should butt confronting the base of the cabinet or cabinet frame.^[5]

   • If your microwave came with a wall template, record that instead equally a drilling guide before you attach the plate.
   • Apply a level to ensure your microwave isn't installed at a camber.
   • Remove any decorative trimming from the cabinet preventing you from placing the mounting plate correctly.
   • If the front of the cabinet has an overhang, place the mounting plate below the dorsum of the cabinet past an equal amount. Otherwise the overhang volition block access to the microwave. For a microwave that requires base-of-cabinet attachments, you may need to saw off the overhang instead.

4. 4

   Locate and drill the correct attachment holes. ^[6] Follow these steps to determine which size holes to drill and where.

   • The bottom edge of the plate should have an area covered in holes. Use a marker to draw circles in at to the lowest degree two holes. At least one should exist completely over a wall stud to back up the microwave's weight.
   • Locate the two or more holes along the upper edge of the microwave. Fill in these with a marking also.
   • Remove the mounting plate. Employ the circles yous drew as a guide, not the mounting plate.
   • Drill a 3/xvi" (5mm) pigsty through whatever circle located on a wall stud.^[7]
   • Drill a three/8" (10mm) hole through whatever other circle.^[8]
   • If your microwave came with a top template, tape it to the base of operations of the cabinet above and drill 3/8"(10mm) holes through attachment points where directed to fasten the microwave to the cabinet base.

5. 5

   Drill a 1.5" – 2" (4-5cm) hole for the ability cord. If your microwave came with a base of chiffonier template, tape this where the microwave tiptop volition be located and drill where instructed for the ability cord. Otherwise, select a spot easily accessible by the power cord and out of the way of normal chiffonier function.

   • If at that place are no electrical outlets within achieve of the string, yous volition need to install a new electrical outlet. Do non use an extension cord.

6. 6

   Secure the mounting plate. Have an assistant agree the mounting plate securely in the correct position equally you fasten it to the wall.

   • Utilise lag screws (lag bolts) in the 3/16"(5mm) holes. These will conduct nearly of the microwave's weight, which is why they are used over the wall studs.
   • Use toggle screws (toggle bolts) in the 3/8"(10mm) holes. The "wings" of the toggle screw go through the hole and pull confronting the wall as the screw is tightened. Pull the mounting plate toward you while tightening toggle screws.^[9]

7. 7

   Mount the microwave. With an banana'due south assist, hang the microwave onto the support tabs on the mounting plate's base.^[10]

   • Snake the ability cable through the hole drilled for this purpose before attaching the microwave.
   • Fasten the microwave to the base of the cabinet in a higher place using screws where directed on the height template. Tighten until the top of the microwave and the base of the chiffonier are flush.

   Advert

1. 1

   Check every surface of your microwave for vents. You don't need a special model of microwave to place information technology on a shelf, just y'all do demand to know where the vents are for proper installation

   • Countertop models normally have vents on the sides and top of the microwave, but back panel vents are common as well.^[11]
   • If you lot are having trouble finding the vents, place the microwave on a tabular array, plug it in, and estrus food or liquid inside. Place your hand nigh each side of the microwave to feel for blowing air.

2. ii

   Remove the turntable and any other loose objects from inside the microwave. This is especially wise if your cabinet is high up, since the tabular array tin easily fall out of the microwave during lifting.

3. 3

   Identify the microwave in a recessed cabinet or on a shelf. Make sure the vents are not flush against whatsoever surfaces or objects. There should be at least an inch of space next to each vent.^[12]

4. 4

   Supercede the turntable and plug the microwave in. If the cord will not reach or is in an inconvenient location, temporarily remove the microwave and drill a pocket-size hole in the cabinet or shelf to snake the cord through.

5. 5

   Make clean the microwave vents every iii months or so. Because the chiffonier does not let as much air movement around the vents, dust will gradually build up and increase the adventure of burn.^[13]

   • Wipe the vents with a damp material while the microwave is turned off.

   Advertising

Add New Question

• Question

  How do y'all install a microwave in a higher place the stove?

  

  Gevorg Grigorian is an Appliance Repair Specialist and the Owner of Chiliad and R Apparatus Repair in Los Angeles, California. With over 12 years of feel, Gevorg specializes in residential and commercial appliance repairs as well as heating, ventilation, and air-conditioning (HVAC) services. Gevorg holds a BS in Business Administration and Management from California State Academy-Northridge.

  

  Appliance Repair Expert

  Adept Answer

  

  Support wikiHow by unlocking this expert answer.

  Information technology'south usually preferred to do this job with two people to make information technology easier. Make sure yous cover the stove and so that it is cushioned merely in case the microwave falls during installation. Y'all will need a level drill and drill scrap to brand the holes needed so that you can add the bracket needed to install the microwave. Unless you already have holes nowadays, y'all will also need to add them to allow ventilation tubes to exist installed.

Ask a Question

200 characters left

Include your e-mail address to become a message when this question is answered.

Submit

Advertisement

• For high chiffonier spaces, take an assistant hold the electrical cable out of the mode or snake it through a hole in the chiffonier while y'all elevator the microwave.

• If in any doubt, refer to the manufacturer's instruction transmission or call the retail shop you purchased the microwave from for more help.

• Proper ventilation is especially of import for microwaves installed in an RV or other vehicle. Consider using a forepart-venting microwave or a kit for venting the cabinet to the outside.

Advertisement

• Practice not use a microwave manufactured in a region with a different electrical standard than your present location. This risks permanently destroying your microwave and starting a fire.

• Placing a microwave'due south vents confronting the cabinet walls or declining to clean them regularly increases the risk of fire from grit buildup.

Advertising

Things You'll Need

• Microwave

For Nether Chiffonier Microwaves:

• Microwave's Mounting Plate
• Drill
• Stud Finder or Hammer
• Pen or Marking
• Level
• Tape (if you accept the paper template)
• 3/16" (5mm) Lag screws (i-4)
• 3/8" (10mm) Toggle screws (2-4)

About This Article

Article Summary X

To install an nether cabinet microwave, offset find your wall studs past tapping with a hammer on the wall until you hear a solid "thud" rather than a hollow sound. Next, position the mounting plate so it'due south level with the bottom of the cabinet and drill holes over the studs and a pigsty for the ability string. When you're set up to fix the plate to the wall, become someone to hold the plate while yous adhere it with lag screws. Once the plate is in place, thread the power cord through the pigsty and hang the microwave on the support tabs. For tips on how to install a countertop microwave, read on!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 158,137 times.

Did this article help you?

Source: https://www.wikihow.com/Install-a-Microwave

Posted by: whiteblaying1956.blogspot.com

Share this post